产品中心
Inicio > Centro de productos > Heavy Duty PE Tarpaulin > Green and Silver PE Tarpaulin, Custom Size, Weight and Thickness

Green and Silver PE Tarpaulin, Custom Size, Weight and Thickness

Green and Silver PE Tarpaulin, Custom Size, Weight and Thickness

    Green and Silver PE Tarpaulin, Custom Size, Weight and Thickness

    Green outside, silver inside — a reversible PE tarpaulin with a heat-welded hem, a rope in all four edges, reinforced corners and galvanised eyelets. Size, weight and thickness made to order.
  • compartir:
  • Contáctanos Consulta en línea

Green and Silver PE tarpaulin, Cut and Welded to Your Size

Green on the outside, bright silver on the inside. The green face blends into a yard or a garden; the silver face is the reflective one, so it is usually turned inwards when the sheet is used as a screen or as a roof over a work area.

Both faces are the same woven PE core with a continuous coating, and the edge is folded over and heat-welded rather than stitched, with a rope run inside the fold on all four sides. Reversible, so either face can be turned out.

Construction

Heat-welded hem, no stitching

The edge is folded over and welded at high temperature, so the coating fuses into one continuous band. There is no row of needle holes along the border — the place a stitched tarpaulin usually starts to leak — and the edge cannot fray.

Rope inside all four edges

A rope runs inside the folded hem on every side, long edges and short. It shares the pull between eyelets instead of letting each fixing point take the load on its own, which is what keeps a sheet from tearing out at the corners in wind.

Reinforced corners

Each corner is covered by a black triangular patch welded over the hem, and the corner eyelet is set through the patch. On sheets from 6 m² upwards the heavier patch is fitted as standard.

Galvanised eyelets

Galvanised eyelets with an 11.25 mm bore are set 1 m apart along the edge, and can be set down to about 30 cm apart where a sheet has to be tied down hard.

Green and silver PE tarpaulin detail
Detail: welded hem with the rope inside and the silver reverse showing, black triangular corner patch and galvanised eyelets.

Specifications

MaterialPE — woven scrim with a continuous coating on both faces
ColourGreen outside, bright silver inside
EdgeFolded over and heat-welded (hot-air), no stitching
ReinforcementRope inside the hem on all four edges
CornersBlack triangular patch welded at each corner, with eyelet
EyeletsGalvanised, 11.25 mm bore, 1 m apart as standard — 30 cm on request
SizeMade to your width × length
WeightMade to your g/m² requirement
ThicknessMade to your requirement
PackingFolded and wrapped for export

Green and silver PE tarpaulin rigged as a lean-to
In use: green and silver PE tarpaulin rigged as a lean-to shelter, silver reverse facing in.

Where It Is Used

Yard and farm storage

Over timber, feed, fertiliser and machinery: the welded hem and the rope inside it spread the load along the edge, so the sheet can be pulled tight and lashed down without tearing at the eyelets.

Transport and equipment covers

On trucks, trailers and boats where a stitched hem would chafe and leak. The smooth welded edge does not fray, and the corner patches take the strain of the tie-downs.

Temporary shelters and canopies

Rigged between posts as a rain or sun cover. Because the size is made to order, one sheet can span an opening without a join down the middle.

Common Questions

What sizes can you make?

Any width and any length, cut and welded to your measurement rather than rounded to a stock size. Send the finished size you need and we quote by area.

Can the weight and thickness be customised?

Yes. Both the weight per square metre and the film thickness are set during production, so the same construction can be supplied as a light cover or as a heavy sheet. Heavier material resists wind load and abrasion better; lighter material is easier to handle and cheaper to ship.

How far apart are the eyelets?

One metre apart as standard, and they can be set closer — down to about 30 cm — where a sheet has to be tied down tightly. The eyelet bore is 11.25 mm.

How is the edge finished?

The edge is folded over and heat-welded at high temperature, then a rope is run inside the fold along all four sides. There are no needle holes, which is the point: a stitched hem puts a line of holes through the coating that water eventually finds.

Are the corners reinforced?

Each corner carries a black triangular patch welded over the hem, with the corner eyelet set through it. On sheets of 6 m² and above the corners are upgraded to the thicker patch as standard.

Is it fully waterproof?

The sheet is a woven PE core with a continuous coating on both faces, so water runs off rather than soaking through, and the welded hems stay sealed. Water can still collect in a slack area, so pitch the sheet so it drains.

Request a Quotation

Send the finished size (width × length), the colour, the weight per square metre or thickness you need, the eyelet spacing and the destination port. We will confirm the price, the welding layout and the production schedule, and can send a material sample and a corner sample before a bulk order.

MENSAJE EN LíNEA

Por favor, introduzca una dirección de correo electrónico válida
Código de verificación No puede estar vacío

PRODUCTOS RELACIONADOS

Binzhou · Shandong · China

Binzhou Taituo Import and Export Co., Ltd

Contact Us

Add: Binzhou, Shandong, China
Tel: +86 19954368176
E-mail: 961336486@qq.com

Copyright © 2026 Binzhou Taituo Import and Export Co., Ltd.

Mapa del sitio
chat

×

Este sitio web utiliza cookies para garantizar que obtenga la mejor experiencia en nuestro sitio web.

Aceptar rechazar