Green is the colour most buyers pick for general yard, farm and garden work: it reads as a working cover rather than a temporary sheet, and it sits quietly against grass, hedge and timber.
The sheet is woven PE with a continuous coating on both faces, and the edge is folded over and heat-welded rather than stitched, with a rope run inside the fold on all four sides. That is what separates it from a cheap tarpaulin: the hem holds its shape when the sheet is pulled tight, and there are no needle holes for water to work through.
The edge is folded over and welded at high temperature, so the coating fuses into one continuous band. There is no row of needle holes along the border — the place a stitched tarpaulin usually starts to leak — and the edge cannot fray.
A rope runs inside the folded hem on every side, long edges and short. It shares the pull between eyelets instead of letting each fixing point take the load on its own, which is what keeps a sheet from tearing out at the corners in wind.
Each corner is covered by a black triangular patch welded over the hem, and the corner eyelet is set through the patch. On sheets from 6 m² upwards the heavier patch is fitted as standard.
Galvanised eyelets with an 11.25 mm bore are set 1 m apart along the edge, and can be set down to about 30 cm apart where a sheet has to be tied down hard.

Detail: the eyelet set through the welded hem, the coated surface beading water, and the same sheet folded with its eyelets along the edge.
| Material | PE — woven scrim with a continuous coating on both faces |
| Colour | Green on both faces |
| Edge | Folded over and heat-welded (hot-air), no stitching |
| Reinforcement | Rope inside the hem on all four edges |
| Corners | Black triangular patch welded at each corner, with eyelet |
| Eyelets | Galvanised, 11.25 mm bore, 1 m apart as standard — 30 cm on request |
| Size | Made to your width × length |
| Weight | Made to your g/m² requirement |
| Thickness | Made to your requirement |
| Packing | Folded and wrapped for export |

In use: green PE tarpaulin over a timber store, edges tied down through the eyelets.
Over timber, feed, fertiliser and machinery: the welded hem and the rope inside it spread the load along the edge, so the sheet can be pulled tight and lashed down without tearing at the eyelets.
On trucks, trailers and boats where a stitched hem would chafe and leak. The smooth welded edge does not fray, and the corner patches take the strain of the tie-downs.
Rigged between posts as a rain or sun cover. Because the size is made to order, one sheet can span an opening without a join down the middle.
Any width and any length, cut and welded to your measurement rather than rounded to a stock size. Send the finished size you need and we quote by area.
Yes. Both the weight per square metre and the film thickness are set during production, so the same construction can be supplied as a light cover or as a heavy sheet. Heavier material resists wind load and abrasion better; lighter material is easier to handle and cheaper to ship.
One metre apart as standard, and they can be set closer — down to about 30 cm — where a sheet has to be tied down tightly. The eyelet bore is 11.25 mm.
The edge is folded over and heat-welded at high temperature, then a rope is run inside the fold along all four sides. There are no needle holes, which is the point: a stitched hem puts a line of holes through the coating that water eventually finds.
Each corner carries a black triangular patch welded over the hem, with the corner eyelet set through it. On sheets of 6 m² and above the corners are upgraded to the thicker patch as standard.
The sheet is a woven PE core with a continuous coating on both faces, so water runs off rather than soaking through, and the welded hems stay sealed. Water can still collect in a slack area, so pitch the sheet so it drains.
Send the finished size (width × length), the colour, the weight per square metre or thickness you need, the eyelet spacing and the destination port. We will confirm the price, the welding layout and the production schedule, and can send a material sample and a corner sample before a bulk order.
RELATED
RELATED
RELATED
RELATED
Binzhou Taituo Import and Export Co., Ltd
Add: Binzhou, Shandong, China
Tel: +86 19954368176
E-mail: 961336486@qq.com
Copyright © 2026 Binzhou Taituo Import and Export Co., Ltd.
Mapa del sitio
Este sitio web utiliza cookies para garantizar que obtenga la mejor experiencia en nuestro sitio web.